Comfort Flow Heating Blog:
Archive for the ‘Heating’ Category

Springfield, OR Heating Tip: What to Expect When Upgrading to Radiant Heating

Monday, November 26th, 2012

If you are thinking of installing radiant floor heating, call the Springfield, OR heating professionals at Comfort Flow. We can help you choose the right type and go over the installation process. First, you’ll need to decide which type of flooring you want, unless you are upgrading.

While radiant floor materials are varied, you need to know that in retrofitting situations, the flooring will need to be torn up. Pipes for radiant floor heating systems are installed beneath the floor, and you’ll need to decide if that is the most cost-effective upgrade for you. Whether you have tile, wood, cement, or another type of flooring, we can help you decide.

Unless you already have a boiler, you will also need to decide between a gas or electric boiler. It will depend on the cost of fuel and your specific situation. Either way, the water will be sent to the right type of pipes underneath the floor, and you heating contractor will know what the right type of piping material to use to match your flooring.

You can also add some hydronic baseboard units if you only want radiant floors in one part of your home. Hydronic baseboards are similar to electric baseboards in the way they heat the home; however, hydronic systems are a lot more efficient than electric baseboards. Both types are installed close to the floor to heat the room as the warm air rises.

If you don’t have the budget to upgrade to radiant floors, or to replace your entire heating and air conditioning system, a Springfield, OR radiant heating expert at Comfort Flow can provide you with further tips and ways to make smaller upgrades to get better overall home efficiency. Contact Comfort Flow for advice or more tips.

Continue Reading

Tags: , ,
Posted in Heating | Comments Off on Springfield, OR Heating Tip: What to Expect When Upgrading to Radiant Heating

Eugene Heating Tips: Common Heating Problems

Monday, November 19th, 2012

If you are having issues with your furnace, heat pump, radiant heating, or geothermal heating system, the Eugene heating technicians at Comfort Flow can help. Many heating problems can be resolved with a minor repair, but it is important to know when it’s time to call for repairs. Here are some common problems and potential causes of heating problems for the different types of systems we can repair and maintain for you.

Call any time if you are experiencing these or other issues with your heater.

Gas Furnace Pilot Light Won’t Light

A broken pilot light is one of the more common problems with gas furnaces, but the light may not be broken. There could be a down draft from the chimney, or another draft near the flame, that is keeping it from staying lit. There could be a clog in the valve, which should be cleaned out with a wire brush before attempting to light it again. Make sure you know how to light your pilot light on your gas furnace. Consult your owner’s manual or call a technician if you aren’t comfortable lighting the pilot.

Heat Pump Not Turning On

Is your heat pump not turning on in heating mode? Always first check the settings to make sure it is on the proper setting, and be sure to also check power switch. It may have been accidentally turned off, or there could be a blown fuse. Check the fuse box for a flipped switch. Also check your owner’s manual for other troubleshooting tips. Call us if you cannot get your heat pump to work in heating mode.

Radiant Heat Not Providing Enough Heat

If your radiant heating system isn’t providing enough heat, always check the thermostat first. Make sure you understand the settings and that you have it set for the desired temperature. Try turning it up about 5 degrees and wait about ten minutes or so to see if that helped. This could mean that the accuracy of your thermostat is off and just needs to be adjusted. Check to make sure your boiler is working if this doesn’t work, or call us.

If everything checks out and you still can’t get your heater to work properly, call Comfort Flow. We’ll send one of our Eugene heating technicians to your home as soon as possible.

Continue Reading

Tags: , , ,
Posted in Heating | Comments Off on Eugene Heating Tips: Common Heating Problems

Eugene OR Water Heater Tip: Choosing the Right Water Heater

Monday, October 22nd, 2012

Choosing the right water heater for your Eugene OR home can be tough decision, given all the different models that are designed to provide better efficiency and a constant supply of hot water. Regardless of the model you choose, always hire a professional to install a new water heater. Because of the advanced technology used to run high-efficiency equipment, only a certified technician should make any repairs to the unit as well.

The expert technicians at Comfort Flow are trained to install, repair and maintain water heaters throughout the service area. Call today if you would like to know more about how to choose the right water heater. Here is a comparison of the two main types to get you started.

Tankless Water Heater

Tankless water heaters save energy by heating the water directly as it goes to the application, such as a dishwasher or shower. This saves energy because there’s no need to keep an entire tank of water heated at all times. In addition, tankless models can work with your existing heating system to save even more energy during the winter.

Before installing a tankless water heater for you, your technician will need to make sure you get the right size for your home and water heating needs. You can also install individual units that are matched for a specific application that uses a lot of hot water, such as a washing machine, so that your main tankless unit will be more effective. Our professional technicians can help you select the right model and size to match your hot water usage needs.

Tank Water Heaters

Even though tank water heaters may not be as efficient as tankless, there have been many improvements in technology in recent years that have improved their efficiency. Finding the proper size and type will depend on several variables, including flow rate calculations for all the hot water applications in the home. Our technicians are trained to help you make these calculations and determine the right size for your home.

When you call Comfort Flow, one of our plumbing experts will set up an appointment with you to go over your options and find the right water heater for your Eugene OR home. We are always glad to answer any questions, so give us a call any time. For repairs and maintenance services, call today to schedule an appointment.

Continue Reading

Tags: , ,
Posted in Heating | Comments Off on Eugene OR Water Heater Tip: Choosing the Right Water Heater

Springfield, OR Heating FAQ: Is It Time for a New Heating System?

Monday, October 15th, 2012

Comfort Flow has been providing Springfield, OR heating services to customers throughout the area since 1961. That’s why customers trust us to help them with all their heating needs, including heating repairs, maintenance, and replacement services. If you aren’t sure whether or not it’s time for a new heating system, give us a call any time.

Meanwhile, here are a few questions to ask as you consider replacing your old heater with a new heating system:

Does your old heater cost too much to operate?

While your old heater may have given you many years of uninterrupted service, you could be paying more than you need to in heating bills. Upgrading to a high-efficiency system, or a heating system that runs on renewable energy, such as a geothermal heat pump system, could dramatically reduce your heating costs. However, it is important to keep in mind that there are other factors to consider before choosing to upgrade.

Does your current heating system need frequent or costly repairs?

If you are paying more money in repair costs than you normally would, it may be time for a heating replacement. We offer an energy savings agreement to help with the cost of preventive maintenance for your new heating system to help prevent repair needs, but eventually all heating systems will need to be replaced. Having to pay a large amount for a heating repair is another reason homeowners choose to replace their heating systems instead of repairing them.

Do you have hot or cold spots in your home?

While hot or cold spots in the home may just require a duct sealing service, inconsistent temperatures in your home could also indicate that it is time for a new heating system. Keep in mind that there are other factors to consider. These include the condition of other supporting equipment, the type and number of thermostats you have in your home, the level of insulation, and how well your home is sealed.

Does your heating system break down often?

If your heating system breaks down often, it could be due to age, improper installation, poor maintenance, or a number of other issues. In any case, frequent equipment failure is not only costly, but it leaves you without heat during the colder months of the year. It may be a more cost-effective decision to replace your heater with a new system, in addition to ensuring your comfort throughout the heating season.

Call the Springfield, OR heating experts at Comfort Flow if you would like to set up a consultation.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on Springfield, OR Heating FAQ: Is It Time for a New Heating System?

Lane County Home Show This Weekend!

Thursday, October 11th, 2012

Join Comfort Flow Heating this weekend at the Lane County Home Show, October 12-14, 2012. We will have a booth for Air Conditioning and Heating solutions as well as a Geothermal education. We would love to meet you and discuss the options for upgrading and maintaining your home comfort systems!

Continue Reading

Tags:
Posted in Air Conditioning, Geothermal, Heating, Home Improvement | Comments Off on Lane County Home Show This Weekend!

Eugene OR Tip: Essential Heating Maintenance Tasks

Monday, October 8th, 2012

Just like your vehicle, performing regular maintenance on your heating and air conditioning system is absolutely necessary. Not only can this keep your heating and cooling system working as efficiently as possible, it can also extend the life of your equipment—both of which can save you money.

In Eugene, OR, it is generally recommended that before each new season you perform regular maintenance on your heating and air conditioning system. For example, after your air conditioning system has sat dormant for during the winter, you should perform some regular maintenance on it before you start running it all the time in the summer.

Here are some of the tasks that we think are essential to keeping your heating and air conditioning system working properly.

Inspect refrigerant levels

Making sure that you don’t have too little or too much refrigerant in your system will make sure that your heating or air conditioning system is operating properly. If you notice that your refrigerant level is too low or too high, adjust it as necessary. Consult your owner’s manual for the correct amount of refrigerant necessary for your particular unit.

Remove Debris

If you have an outdoor unit with a door or hinge that opens, make sure the unit isn’t clogged with leaves, dirt or other organic material. This can cause the unit to vent improperly and can also be a fire hazard.

Check Drains, Refrigerant and Condensate Lines

Making sure that the fluids in your heating system are flowing properly is crucial to proper operation of your unit. Check any drains or drainage lines to make sure that your unit is disposing of condensate efficiently. If you have an outdoor compressor, you should also check the associated tubes for wear or damage.

Check Fan Blades and Motor

For indoor units like a furnace or outdoor units like a ductless mini split, you should check the blower or fan motor for any obvious signs of damage or wear. For outdoor units, make sure there isn’t anything obstructing the fan or if there is damage to any of the blades.

Check Burner, Ignition

For indoor furnaces and heating systems, make sure that your burner assembly is clean and operating properly. Also, check your ignition system to make sure that it isn’t obstructed or dirty.

Clean Air Filter

Many houses have air filters in the return air duct of their heating system. These filters make sure that any dust or dirt that is in your ductwork doesn’t get recirculated into your home’s air supply. Many filters you can just slide out of the unit and replace. Check your owner’s manual to see which size or model of filter is appropriate for your heating unit.

If you would like to know more aout how to properly maintain your heating system or if you would like to schedule a visit with one of our heating experts, then contact Comfort Flow today!

Continue Reading

Tags: , , , ,
Posted in Heating | Comments Off on Eugene OR Tip: Essential Heating Maintenance Tasks

Eugene OR Heating Guide: Commercial Heating Maintenance

Monday, October 1st, 2012

A commercial heating system is a powerful and complex piece of machinery, and you rely on it to do a large and important job. Because of this, it’s very important that you make sure your system is prepared for the long heating season ahead, and the best way to do that is with regular commercial heating maintenance from an experienced Eugene OR heating professional.

Benefits of Regular Maintenance

Regular commercial heating maintenance will benefit you in several ways. To begin with, it will ensure that your heating system is working at peak energy efficiency levels, and that means lower heating bills for you all winter long. A system that isn’t properly maintained on a regular basis may still work effectively, but it will likely be using more energy than necessary to run, and that costs you money.

Your furnace is also less likely to need emergency repairs when you have a technician inspect it prior to the start of the heating season. On this type of visit, they can often find parts that need to be replaced before the break down completely, and they can address any other minor issues they find that would have turned into larger problems later on.

Ongoing professional maintenance is the best way to extend the life of your system as well. Since your commercial heating system was such a substantial investment to begin with, you want to make sure you get the most possible out of it, and keeping up with maintenance is the most effective way to do that.

Why You Need a Qualified Professional

Because a commercial heating system differs from a residential system in several fundamental ways, it’s important to have a technician with experience working with commercial systems caring for yours. That way, you can have confidence that all maintenance is being carried out properly and that your system will work properly when you need it to.

To schedule a maintenance visit for your commercial or residential heating system in Eugene OR, give Comfort Flow Heating a call today!

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on Eugene OR Heating Guide: Commercial Heating Maintenance

Eugene, OR Heating Tip: Make Your Heating System More Energy Efficient

Monday, September 24th, 2012

Everyone wants to ensure efficiency in their heating and air conditioning systems, so when the opportunity comes to perform a handful of basic tasks or upgrades that will do just that, many people in Eugene, OR jump at the chance. Specifically, when it comes to your furnace there are quite a few things you can do that will make your system more efficient without having to replace the entire system. Here are a few of them:

*  Regular Maintenance – The easiest way to ensure any heating system uses as little energy as possible is to have regular maintenance performed on it. A tune up performed by a professional once a year is the best way to do this, though you can also benefit from cleaning in and around the furnace room yourself every month.

*  Filter Checks – Check and clean filters according to their manufacturer’s guidelines to ensure there are no clogs in the system. This will greatly reduce the cost of operating your furnace.

*  Inspect and Repair Ductwork – If there are leaks or gaps in ductwork, it can result in a significant loss of heating during operation which will of course greatly reduce your heating efficiency.

*  Vent Damper – A vent damper is a good fit for older furnaces that don’t have mechanisms in place to protect against losses of heat through the chimney when your furnace is not firing.

*  Derating Your Furnace – Older furnaces are often oversized and can be derated to use less energy without having any effect on your home’s comfort levels. The modifications are simple, though not necessarily allowed in every municipality.

The best way to know for sure which of these things are best for your furnace is to talk with a Eugene, OR heating professional about them. Derating and vent damper installation especially are very effective in reducing energy loss but may not be the best option depending on the age of your furnace and how close it is to needing replacement.

A Comfort Flow Heating technician can help you review all of your options before making a decision.

Contact Comfort Flow Heating today!

 

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on Eugene, OR Heating Tip: Make Your Heating System More Energy Efficient

Eugene, OR Heating Guide: Tips on How to Navigate Buying a Furnace

Monday, September 17th, 2012

Replacing an older furnace is a great way to save money by lowering your energy bills. That’s because newer models are much more energy efficient than those made even 15 years ago. If you’re in the market for a new furnace in Eugene, there are some things you should think about before spending any money. Doing a little bit of research upfront can end up saving you a lot in the long run.

Size is one of the biggest things to consider. A system that’s too small will have to work harder to get your home to the desired temperature, causing it to continually draw in more fuel, greatly increasing your energy bill.

Some people try to overcompensate for this by buying a furnace which is bigger than their home needs. The problem with doing this is that a larger system will cycle on and off more frequently, which is also counterproductive to saving energy. The proper size system for your home falls in between these two extremes and cycles on and off at the right times to keep your home comfortable.

Efficiency is also important and can be seen in a system’s AFUE (Annual Fuel Utilization Efficiency) rating. The higher the AFUE rating number, the better the system is at garnering heat from a set amount of fuel. The more efficient a system is, the lower its emissions, and that’s also better for the environment.

One drawback to a system with a higher AFUE rating is the higher initial installation cost. The benefit is lower energy bills for the life of the system, which can add up to significant savings over the long run.

If you’re looking at a specific brand of furnace, it may pay to do some checking online or with a professional Eugene OR heating company to see how the competition stacks up. Someone who works exclusively with HVAC systems can give a lot of insight into what brands and models are tried and true, which ones seem to need frequent repair, and even which ones haven’t been on the market long enough to have been thoroughly tested over time. All of these are important things to consider before making your final purchasing decision.

For any help choosing a furnace in the Eugene area, give Comfort Flow Heating a call!

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Eugene, OR Heating Guide: Tips on How to Navigate Buying a Furnace